does anyone know the size and type of fastener used to secure pickup coils 1985

[mtc]

i think is M6

but what is the length?

and head type

i could use cap screw right?

and is there a washer in there?

[aviationfred]

I dont know the length, diameter or thread pitch, but the bolt, washer and nut are available new from Yamaha. #11, #12, and #13 in the diagram


https://www.partzilla.com/catalog/yamaha/motorcycle/1985/fj1100n/electrical-2



Fred

[mtc]

I dont know the length, diameter or thread pitch, but the bolt, washer and nut are available new from Yamaha. #11, #12, and #13 in the diagram


https://www.partzilla.com/catalog/yamaha/motorcycle/1985/fj1100n/electrical-2



Fred

thanks but looking for the bolts that hold the pickup plate, not  the rotor

[red]

MTC,

Decode Yamaha bolt numbers here:

https://www.yamahastarbolt.com/technical-library/decode-yamaha-part-numbers/

Once you have the correct Yamaha Part Number for a bolt, scroll down and find the Part Number grouping that matches your number, on the linked web site.  Digit locations indicate the specs of the bolt.
.

[aviationfred]

My apologies, I misread your post and listed the bolt that is for the main coils.

I believe what you are looking for are the 2 small bolts in this diagram. #5 in the drawing. They are available from Yamaha and probably RPM.

https://www.partzilla.com/catalog/yamaha/motorcycle/1985/fj1100n/pickup-coil-governor

Fred

[Old Rider]

If i remeber right you can use the same bolts used on the top camchain guard.

[FJ_Hooligan]

From the part number: 98517-06012-00

It's an M6 x 12mm long.  The stock screw has a captive washer.

Should be able to get one at any hardware store

[mtc]

From the part number: 98517-06012-00

It's an M6 x 12mm long.  The stock screw has a captive washer.

Should be able to get one at any hardware store

thank you everyone, i am sure it is M6 since that is what the dyna instruction says, but it's 20mm long, i guess i can use a cap screw head, i just needed the length,

when i click on the  screw i see no washer

https://www.partzilla.com/product/yamaha/98517-06012-00?ref=c781fe29972bf8524f07297f5deed185810b3760

[mtc]

MTC,

Decode Yamaha bolt numbers here:

https://www.yamahastarbolt.com/technical-library/decode-yamaha-part-numbers/

Once you have the correct Yamaha Part Number for a bolt, scroll down and find the Part Number grouping that matches your number, on the linked web site.  Digit locations indicate the specs of the bolt.
.

thank you very much

[FJ_Hooligan]

If you use the link Fred provided, the screw is listed as: SCREW, WITH WASHER

[mtc]

If you use the link Fred provided, the screw is listed as: SCREW, WITH WASHER

thanks, i just went and bought hex cap screws but it is still no washers


but i keep looking for sizing, where did you actually see the m6/12mm sizing?


https://www.ebay.com/itm/Yamaha-OEM-Pan-Head-Screw-98517-06012-00-/152464088061

[Pat Conlon]

https://www.partzilla.com/catalog/yamaha/motorcycle/1985/fj1100n/pickup-coil-governor

Read the #5 part number ^^^ 9857-06012-00

See the middle numbers? Diameter comes first, then the length.

[mtc]

https://www.partzilla.com/catalog/yamaha/motorcycle/1985/fj1100n/pickup-coil-governor

Read the #5 part number ^^^ 9857-06012-00

See the middle numbers? Diameter comes first, then the length.

sorry need to be spoon fed everything, thanks

[Sparky84]

https://www.partzilla.com/catalog/yamaha/motorcycle/1985/fj1100n/pickup-coil-governor

Read the #5 part number ^^^ 9857-06012-00

See the middle numbers? Diameter comes first, then the length.

sorry need to be spoon fed everything, thanks

Are you still in the high chair at home   

[red]

.
Keep yer heads low, squad; snipers are in the area!

We'll get everybody through, just hang tough.
.