News:

This forum is run by RPM and donations from members.

It is the donations of the members that help offset the operating cost of the forum. The secondary benefit of being a contributing member is the ability to save big during RPM Holiday sales. For more information please check out this link: Membership has its privileges 

Thank you for your support of the all mighty FJ.

Main Menu

Crack in Fairing Needs Fixing & and I'm Looking for Tips & Tricks

Started by FJ1100mjk, March 24, 2011, 07:10:53 PM

Previous topic - Next topic

FJ1100mjk

Hello:

I just bought an '85, and I have it in pieces to go over it real well before the riding season starts. Previous owner must've crashed it because I've found scrapes on its right side. I found (well actually it stood out when I was looking at the bike before I bought it) this crack in the front fairing. Is this a crack that can be fixed by a shady tree mechanic such as myself, or should it best be handled by a professional?

I read where somebody used something call Plastex with good results. Plastex comes in colors (white, black. If anyone has used this product (or a similar one with good results) before, could you give me some tips on repairing a crack like this?

Thanks in advance.

Marty





Platinum Zircon-encrusted Gold Member

Iron Balls #00002175
www.ironballs.com


SkyFive


I have the same problem. What I'm going to do is; use a pin guage drill bit to stop drill all the cracks. Then I'm going to clean, sand and fiberglass the cracks on the inside being careful not to get any fibergalss resin on the outside painted surfaces.

junkyardroad

The fairing is ABS plastic. (Acrylonitrile Butadiene Styrene)  It melts around 220 deg +/-.  There were several similar cracks in my fairing, including the left upper windsheild strut cracked thru.

Go to Harbor Freight and get the white plastic welding rods, they're cheap.  Use an inexpensive pen type electric solder wand. Mine is from Radio Shack circa 1980.  Using the wedge shaped tip, press the hot iron into the plastic while pressing the ABS rod into the molten puddle. I was constantly twisting the iron to distribute the plastic and made a row of "welds" about the diameter of a pencil eraser.  They looked like the "stacked dimes" type of tig weld you have probably seen.  Finish the repair with a high speed sander like a Dremel, I used a die grinder with a scotch brite type pad.  Use a high-build primer and block till the surface is flat. SEM makes an adhesion promoter in an aerosol that makes paintwork much easier.

Let the primer cure for a couple of weeks.  Mine printed thru the paint after curing only a week, but nobody can find it until I show them.

HTH

FJ1100mjk

Fellas,

Thanks for the tips.

I just happen to be going to Harbor Freight tomorrow to pick up a compression tester that has an adapter to fit the smaller diameter spark plug holes on my FJ. I'll look at the plastic weld rods and cheap soldering pen.

I'm looking at closing up the crack enough, so that it isn't so noticeable, and to keep it from spreading. I was thinking of doing the weld from the inside, but I wasn't wanting to wreck the OEM paint job. Based upon your experience, do you think that it is possible to fix it from the inside, and not disturb the original paint job?

Thanks again.
Marty
Platinum Zircon-encrusted Gold Member

Iron Balls #00002175
www.ironballs.com


junkyardroad

Quotepossible to fix it from the inside, and not disturb the original paint job?

Probably not.  You could try to not melt thru, but the fix would be weak.  Better to repaint with a solid repair.

Good luck with the fix.

wraivi

Hey,

I had a similar thing plus some broken mounting points. I used a 2 pack epoxy resin and woven fine fibre-glass cloth, which is also used for joining wings on large scale model aircraft, incredibly strong and easier to handle than fibre glass resin - I use both regularly, but the epoxy resin reinforced with this cloth is super strong and will solve your problem - it'll be stronger than original! Good Luck.

FJ1100mjk

wraivi:

Thanks for the tip on epoxy resin and the cloth. May need it for a back up, because....

I went and ordered the Plastex fix it (clear). I'll give it a try and report back my success, or lack thereof.

Marty
Platinum Zircon-encrusted Gold Member

Iron Balls #00002175
www.ironballs.com


brdprey

 :morning1: i know I'm new here but I've been doing some research on this topic.
this seems to be the best I've seen yet.
http://urethanesupply.com/howtorepair.php
:bye: hope it helps I'm waiting on some financial relief before i can try it.